If you’ve ever asked yourself if it’s possible to extend a Pax wardrobe so you don’t waste the space over it or if you’ve wondered about the easiest way to turn your IKEA Pax wardrobes into custom built-ins you’re in the right place!
We have the best IKEA wardrobe hack coming up for you! Oh, and did I mention that this Pax wardrobe hack is 100% renter-friendly, too?!
This is what our Pax wardrobes looked like for the first few months after assembling them.
They were full of stuff, the doors were wonky and even the top of the wardrobes was crammed full of boxes and other things we rarely use.
But after just a few hours of work – yes, that’s all it takes – our ugly wardrobes (and all of the junk) have disappeared!
Okay, so none of the junk has actually vanished and everything is still just as full and messy as it was before but now everything is completely hidden behind our custom Pax doors.
The best thing about this hack is that no part of the wardrobe actually touches the walls making a super renter-friendly project, too.
There’s no complicated carpentry involved, nothing is drilled to the walls and you don’t have to have any mad DIY skills to completely turn an IKEA Pax into a fitted wardrobe.
And, this is a super budget-friendly project, too! We’ll share a full cost breakdown at the end of the post.
If you have high ceilings and don’t want to waste the space over your Pax wardrobes, this is the perfect IKEA hack for you!
So, how do you extend a Pax wardrobe and make it look built in?
The secret to this IKEA Pax hack lies in the cladding of the doors. The actual Pax wardrobes aren’t actually extended, just the doors are!
The doors are covered in cladding which not only allows you to extend them but enables you to combine them with other IKEA cupboards (one part of our wardrobe is a Billy cupboard) and create a completely seamless and custom built-in piece of furniture.
This is also why none of the wardrobes actually touch the walls – the doors just extend upwards, downwards and sideways (more on that later) and don’t touch any part of the surrounding walls making it possible to completely remove this built-in (looking) wardrobe without leaving a trace.
Don’t worry if this sounds complicated – it really isn’t difficult and we’re sharing the exact step by step guide on how to extend a Pax wardrobe and make it look completely built-in!
This is what you will need to extend an IKEA Pax wardrobe:
This post contains affiliate links. We only recommend products we love and think that you will, too! Read our full disclaimer here.
- Pax wardrobes with doors – If you’re buying a new wardrobe just opt for the cheapest doors available which is exactly what we did.
- 1 x additional door (more on why you will need an additional door later in the tutorial)
- Wood glue – This is our favourite wood glue. You’ll need quite a lot of it!
- 3mm thick HDF or MDF panels – We recommend getting the panels cut for you as it’s extremely important that the panels are exactly the same size
- Screws & Nails
- Wood Filler
- Primer – Any wood primer will do – we used one we had left over from other projects.
- Paint – We used this absolutely gorgeous Bare Concrete paint by Crown Paints.
- A couple of offcuts of wood (you’ll only need these if you are extending to the sides, too)
- Handles – We used these brushed gold handles.
- Cordless Drill & Drill Bits
- Kreg Jig – This is our newest tool and I can’t believe how we ever DIYed without it! It makes connecting pieces of timber so easy! Definitely an investment worth making but, as always, hire any tools that you think will only use once!
- Stanley Knife
- Nailer – This is optional as you could just use wood glue but it will make the project quicker and easier if you have one. This is the nailer that we have, love and use for all of our projects.
- Circular saw
- Paintbrush – We’ve been using the same set of paintbrushes for almost 10 years! We absolutely love them and still use them for every painting project! Good quality brushes are the secret to getting a perfect paint finish!
- Clamps – We use these quick-grip clamps for all of our projects.
- Tape measure & Pencil
How To Extend Your Pax Wardrobe & Make Them Built-In:
This guide is fairly long as we’ve gone into a lot of detail so that you know everything about how to extend your Pax wardrobe. Don’t worry though, it is an easy project and there are only 3 steps to make your Pax wardrobe look built-in.
First, you have to extend the doors, then cover them in cladding and finally, there’s a bit of priming and painting to do.
1. Planning The Wardrobe Transformation
Off the peg wardrobes generally come in 50 cm sections so can be tricky to get them to perfectly fit along your wall or in an alcove.
In our case, the recess for the wardrobe is 3.4 metres wide which means we’d only be able to fit three 1 metre wardrobes into the space and would waste a whopping 40 centimetres if we didn’t opt for a custom-built solution.
Not wanting to spend a fortune on custom cabinetry, we had to get creative to make the most of the limited storage space we have and came up with a solution that not only looks great but utilises every last centimetre of usable space.
That’s why we combined our three IKEA Pax wardrobes with a Billy cupboard.
I know that a combination of Pax and Billy seems a bit mad as both cupboards are completely different sizes, but this IKEA hack completely hides the cupboards and allows you to combine different furniture models to create a wardrobe that’s a perfect fit for your home.
The doors are all cladded to look the same so you’ll end up with a wardrobe that looks completely bespoke without having to break the bank.
You can combine any IKEA furniture for this wardrobe hack as long as it has a door. I would recommend trying to use cupboards that are roughly the same height (like Pax + Billy or Pax + a tall Method cupboard) though as it will make the process easier.
The length of the strips of timber will depend on how tall your room is. It is extremely important to leave a gap at the ceiling and floor though so that you can easily open your doors.
We recommend leaving at least 15mm clearance at the bottom and 25mm clearance at the top. Definitely measure a couple of times to make sure your measurements are correct.
If you live in an older property where the ceilings and floor aren’t level, leave a bit more of a gap to make up for any wonkiness.
2. Extending The Wardrobe Doors
Depending on how much you’re extending your doors by, you’ll also have to extend the door itself.
The cladding strips are really thin and would be strong enough if you’re only extending the door by about 10cm but, if they extend over the edge of the door by any more than that, the cladding will be too wobbly and bendy.
How to extend Pax wardrobe doors
We purchased the cheapest doors that are available for the Pax wardrobes which are called Forsand. Pax doors are just under 50cm wide and to cover them you’ll need 10 x 47mm wide strips with a 3mm gap between them.
As we extended our Pax wardrobes by about 40cm, we had to lengthen the door slightly to be able to have something to stick the cladding to. This is where you will need the additional Pax door.
The additional door is already the perfect width that you need, so you just have to cut it into pieces to be able to attach it to the other doors. In our case, all pieces are 38cm long which meant that we were able to cut 6 extension pieces out of one door.
Just chop it into pieces with a circular saw making sure to cut as straight as possible (we clamped a steel ruler in place to cut along).
Obviously, the measurements for this additional piece will vary depending on the height of your room.
It doesn’t matter exactly where the holes are but we’d recommend adding about 5 holes spaced out equally across the width of the door.
How to extend Billy doors:
Billy doors are 40cm wide. To cover them you’ll need 8 x 47mm wide strips with just under a 3mm gap between them (we just eyeballed the distance between the slats when attaching them).
To extend the Billy door we used the same method as for the Pax door. We used a piece of timber that was roughly the size we needed in the IKEA bargain corner and just had to shorten it slightly so it was the right length to extend the Billy door.
The only difference with the Billy extension is that it’s much higher as Billy cupboards aren’t as tall as Pax (we have the 236cm version).
This means that the extension is about 80cm long. We were worried that the long extended piece could snap off so decided to give it some additional support by screwing a flat piece of steel to the back of the cupboard.
It’s not the prettiest of things and I’m not even sure it’s totally necessary but it gives me peace of mind and is on the inside of the door so no one will actually ever see it.
Once you’ve extended your doors, the fun assembly of the project can begin!
Add The Cladding
Lay your door on a flat surface and make sure that it’s dust free and clean. Then start to attach the timber strips one at a time making sure to use a spacer to keep an equal distance between each of them.
For the Pax door, you’ll need 10 strips of timber. Because the gap between each panel on the Pax doors is 3mm, you can use one of the timber strips as a spacer to give you the perfect sized gap. Just wedge it between two timber strips while the glue dries which makes this step surprisingly easy and quick.
The only thing you have to measure is the overhang of cladding at the bottom of the door which should be about 5.5cm. Definitely make the overhang less if you have wonky floors or a carpet though!
We also nailed a couple of nails (one at the top, one in the middle and one at the bottom) into each strip of timber with our nailer to make sure the strips couldn’t move around while the glue dries and to make sure they are firmly attached.
Our nailer is our favourite ever tool and we always recommend it and use it much more than we ever thought possible.
Having said that, it is expensive so you could just glue them in place with some good quality wood glue which I think should be strong enough to hold them in place. It’ll just take a bit longer to assemble the doors as you’ll have to wait for the glue to dry after attaching each strip.
When attaching the strips, it’s best to work from the outer edge inwards. When you get to the middle strips you can then make any slight adjustments to the gap between the strips just in case the gaps aren’t perfect.
We had a couple of doors where we couldn’t get the gap to be exactly 3mm so just eyeballed the distance between the last two strips and you honestly can’t notice a difference.
When attaching the strips to the Billy door, the gaps will be ever so slightly smaller which is why you won’t be able to use another panel as a spacer.
To be able to create equal gaps we glued the two outer pieces of cladding in place first and then just added the other cladding and guestimated the distances between each strip of timber.
You can’t tell a difference at all between the distances on the Pax doors and the gap on the Billy door.
Fill The Bottom Overhang
The bottom of the cladding hangs over the bottom end of the door by 5.5cm, giving you a 1,5cm gap at the bottom. (You may want to adjust this measurement to give you more clearance if you have a carpet or wonky floors).
Because there’s 3mm space between each panel, there are gaps where they hang over the edge of the door.
To fill these gaps just cut one of the additional pieces of cladding you ordered into roughly 45cm long pieces (less if you’re working on a Billy cupboard). You can easily do this by scoring the wood with a Stanley knife and snapping the wood as it’s so thin.
Then glue it over the inside of the overhanging cladding and clamp it in place.
As you can see, we did this after we’d already reattached the doors but I’d definitely recommend doing this step before you put the doors back!
Fill The Gaps To The Walls
You may be lucky and your Pax fits perfectly into your alcove or along the wall but if like us you are left with little gaps you will have to fill these to make your IKEA Pax wardrobes built-in and look like part of the wall.
Usually, we would attach the timber to the wall, but we wanted this to be a renter-friendly hack we attached to the wardrobe instead.
To do this, screw or nail a batten to the side of your Pax wardrobe. The piece of timber you use has to be wide enough for you to be able to glue the additional strips of cladding you’re using but also deep enough so that you can easily nail it to the side of Pax.
We’d recommend using some timber that’s at least 48mm deep to give you enough space to be able to screw into the timber.
This bit of the project is definitely a two-person job as you have to hold the timber you’re screwing (or nailing) to the side of the wardrobe at the right level so that the cladding will be flush with the rest of the doors.
As you can see, we used an offcut of the cladding so that I was able to hold the timber at exactly the same level while Jan nailed it in place.
I’m not going to lie, this is super pfaffy, especially as you can’t open the wardrobe door while you are working. There was definitely a lot of cursing involved and attaching this one piece took longer than assembling a whole door.
As you can see, we also had to cut out a small piece of the cladding so that it would fit around the skirting. As the wood is so thin, I just used a Stanley knife to cut it out.
4. Prime & Paint
Fill any small holes from the nails with some wood filler, wait until it’s dried and then sand everything smooth with some 120 grit sandpaper (ideally followed by 180 grit sandpaper to make it extra smooth).
I would definitely recommend painting the doors before you attach them because it will make it so much easier to paint the edges of the doors which is almost impossible when they are attached to the wardrobes. If you’ve ever attached Pax doors before, you’ll know why I was too lazy to take them off again!
Next, give everything a coat of primer. I just used a paintbrush for this but you could use a roller if you prefer. The reason I prefer to use a paintbrush over a roller is because it’s easier to achieve a smooth finish and I find that roller often leaves a slightly stippled surface.
The secret to a super smooth finish and no visible brush strokes is to use a quality paintbrush and to sand between every coat of primer and every coat of paint.
I’ve been recommending the same paintbrushes ever since sharing our DIY adventures here. We love them so much and still have the exact same paintbrushes we bought over 10 years ago and still use them for all projects. I honestly can’t recommend them highly enough!
The second secret to a super smooth finish (which I also bang on about any chance I get) is not to skip sanding!
Sanding between coats of paint (obviously wait for them to dry first) is the only way you’ll end up with a durable and professional finish. Sanding removes imperfections and the odd brush stroke but, most importantly, it removes any raised grain making the surface super smooth. This step only has to take a couple of minutes but will make all of the difference!
When the primer has dried, all that’s left to do is give your wardrobes a coat of paint. We tried the Elle Decoration range by Crown paints for the first time and loved it. The paint itself is lovely to work with. It’s really smooth, thick and covers amazingly well.
5. Finishing Touches
The last thing to do is attach and adjust the Pax doors and add some handles.
When attaching the door to the wardrobe, we recommend attaching the hinge to the door and then attaching the door to the wardrobe. We tried it the other way around and it just didn’t work.
If you’ve ever attached Pax doors, you’ll know that it’s a bit of a pain to get them to line up and hang perfectly. I’m not going to lie, the panelling you’ve added doesn’t make this step any easier!
You have to make sure there’s a gap between the wardrobe doors so that you can open them without the edges catching.
This inevitably means that there’ll be a lot of adjusting necessary to get the doors to hang perfectly. It’s nothing difficult to do, but it does take a bit of time to get the Pax doors perfectly aligned.
Choosing handles that slot between the doors probably didn’t make adjusting the doors any easier as we needed to leave a gap for the handles as well as between the individual doors. It worked but I’d recommend choosing handles that you attach to the front of the wardrobes to give you more flexibility when adjusting the doors.
How much does it cost to extend a Pax wardrobe?
I know it’s always important to see how much it costs to do these projects, especially as things have a way of adding up quickly. I honestly think this project is a total bargain though as there’s absolutely no way you’d be able to achieve custom built-in wardrobes for so little money otherwise.
Cost Breakdown for 6 doors + 1 Billy cupboard (doesn’t include the cost of the actual wardrobes):
- HDF Cladding | 140€ (If you order your cladding at CNC Creations, don’t forget to use the code littlehouse5 to get 5% off)
- 1 additional Pax door | 15€ (we picked ours up in bargain corner)
- Filler | 2€
- Wood Glue | 8€
- Nails | 3€
- Sandpaper | 2€
- Primer | 10€
- Paint | 40€
- Handles | 43€
Total: (approximately) 263€ (£225)
This works out at just about 38€ (£33) a door (+ the actual door itself)
Top Tips When Extending Pax Wardrobes
- Don’t attempt this Pax hack with wood that’s thicker than 3mm max! You won’t be able to open your doors!
- Leave at least a 1.5cm gap at the bottom and 2.5cm gap at the top of the doors.
We live in a building that’s brand new and even then the floors and ceiling weren’t 100% level. If you live in an older property you may have to leave more of a gap to allow for wonkiness.
- Don’t forget about your ceiling! If your cupboard doors go (almost) all the way up to the top of your room will you still be able to open them? Are there any light fittings or other things like smoke detectors in the way?
- Check the bargain corner for the additional door you need. We picked ours up there for much less and it doesn’t matter what it looks like as you’ll be cutting it up and covering it anyway! Just try to get the same door as the ones you already have as there are slight differences in the thickness.
- Order a couple of additional strips of timber cladding to cover any gaps at the side and the overhang at the bottom of the wardrobe.
- Choose doors that are all the same. You’d be surprised at how much the different designs vary in thickness which will make it more difficult to join the piece together or get a flat look when adjusting the doors later on!
Pros and Cons of Extending a Pax Wardrobe
- It’s a super affordable upgrade and much cheaper than any other built-in option
- It’s an easy and completely beginner-friendly project
- It’s fairly quick to do
- It’s totally bespoke and you can make something that fits in your home perfectly
- It’s ideal if you have wonky walls as nothing is actually attached to them
- Great way to make the most of the space above your wardrobes
- It’s perfect for renters as it’s not attached to the wall
- You can only extend the wardrobe by about 40 cm before it becomes wobbly
- Billy doors are slightly thinner than Pax doors and you can see nail bumbs on the back of the Billy door if you use a nailer to attach the cladding (you obviously won’t have this problem if you don’t use a nailer).
- Adjusting Pax wardrobe doors is a pain and the cladding doesn’t make the process any easier. It takes a long time to get the doors to hang perfectly.
- Watch your toes! If you extend downwards you will reduce the clearance so risk squashing your toes when you open the doors. Obvisously, you don’t have to extend downwards and if you’re accident prone you may not want to. (I’m speaking from experience – or rather one of my toes is!).
It is possible to combine different types of IKEA furniture using this hack. It doesn’t matter if you’re combining Pax and Billy or Pax and Method. Just make sure to use pieces of furniture that have doors that you can attach the cladding to.
None! That’s the beauty of this project. You just extend the doors and don’t have to worry about building any complicated structure or buying additional cupboards. All you have to do is extend your doors!
Our IKEA Pax wardrobes are all about 38cm taller. We wouldn’t recommend making them taller than that as they will start to wobble and the connections can become less secure.
Upgrading each door took about 30 minutes in total. Priming and painting took about another 3 hours and adjusting the doors about another hour. So, in total, it took about 7.5 hours to completely transform our Pax into built-in wardrobes.
If you’ve ever wondered about how to extend your Pax wardrobes or how to combine Pax and Billy (or other IKEA furniture) I honestly can’t recommend this Pax built-in wardrobe hack highly enough!
Although these wardrobes are totally bespoke and look super high-end, you need almost no tools (you can just glue the cladding if you don’t have a nailer) and almost no DIY skills.
This IKEA Pax wardrobe hack gives you a gorgeous custom built-in cupboard without the need for expensive tools and just the most basic DIY skills!
Is the top of your wardrobe also filled with boxes of junk and clutter? Have you ever attempted an IKEA hack? Do you find adjusting hinges as frustrating as we do? Let us know what you think of this Pax hack in the comments below. We can’t wait to hear what you think!